|Required Tools and Supplies|
|PS-4 Engine Oil
1 Gallon (3.78 L)
1 Quart (946 mL)
|Engine Oil Filter|
|T40 TORX® socket||6mm Allen Socket|
|2.5-inch (64mm) Oil Filter Wrench||8mm Socket|
|Torque Wrench||Grease Gun|
|Shop Rags||Safety Glasses & Nitrile Gloves|
To learn more about tools, read the Tools and Fasteners Guide.
When changing the oil on your Polaris Scrambler, always wear safety glasses and nitrile gloves. The PS-4 Full Synthetic Oil Change Kit is part number 2877473. The Extreme Duty Oil Change Kit is part number 2878924.
To change the oil and oil filter on a Scrambler XP 1000 S, follow these steps:
1. Park the vehicle on a flat, level surface in a well-ventilated area.
2. Place the transmission in park.
3. Set the parking brake.
4. Start the engine and allow it to warm up at idle for 2 to 3 minutes.
5. Stop the engine.
6. Remove any debris near the dipstick and remove the dipstick.
7. Clean the area around the oil drain plug.
8. Place a drain pan under the engine crankcase. Tip: Place a rag in the bottom of the drain pan to prevent splashing of oil.
9. Remove the drain plug with a 6mm Allen socket. Allow the oil to drain completely. Caution: Hot oil can cause burns to skin. Do not allow hot oil to contact skin.
10. Using a T40 TORX® socket, remove the oil filter cover plate by loosening the three fasteners holding it in place.
11. Using a 2.5-inch (64mm) oil filter wrench, turn the filter counterclockwise to remove it.
12. Using a clean dry cloth, clean the filter sealing surface on the crankcase.
13. Lubricate the O-ring on the new filter with a film of fresh engine oil. Check to make sure the O-ring is in good condition.
14. Install the new filter and rotate it clockwise by hand until the filter gasket contacts the sealing surface, and then turn it an additional 3/4 of a turn. The filter is part number 2520799. It is included in both oil change kits.
15. Replace the oil filter plate. Torque to 7 ft-lbs (9 Nm).
16. Install a new sealing washer on the drain plug. The sealing washer is part number 5812232. Notice: The sealing surfaces on the drain plug and crankcase should be clean and free of burrs, nicks or scratches.
17. Reinstall the drain plug. Torque to 12 ft-lbs (16 Nm).
18. Clean any residual oil off the vehicle.
19. Add 2 quarts (1.9 liters) of the recommended oil. Do not overfill.
20. Reinstall the dipstick.
21. Start the engine. Allow it to idle for 1 to 2 minutes.
22. Stop the engine.
23. Check for leaks.
24. Check the oil level. Add oil as needed to bring the level to the upper mark on the dipstick.
25. Wipe up any residual oil that may have collected on vehicle components.
26. Dispose of the used oil and filter properly.
27. In addition to changing the engine oil, make sure to grease the propshaft and clean the spark arrestor.
28. Access the grease zerk on the propshaft through the chassis frame on the right side of the vehicle.
29. Then move to the spark arrestor in the rear of the vehicle.
30. Start by removing the four silencer cap fasteners with a 3/8-inch socket and remove the silencer cap.
31. Using an 8mm socket, loosen the spark arrestor fastener and pull out to remove. Clean as needed.
32. Reinstall the spark arrestor. Torque the fastener to 8 ft-lbs (11 Nm).
33. Reinstall the silencer cap and fasteners. Torque to 10 ft-lbs (14 Nm).
Programmable Service Interval
The service interval counter on your Scrambler decreases as engine operation hours increase. Change your engine oil and filter at the recommended service intervals.
To reset or change the service interval:
1. Press and hold the MODE button to enter the Options Menu. "OPTIONS" will display on the screen for 3 seconds before showing the first menu item.
2. Select "Service Hours" from the Options Menu by pressing the MODE button.
Reference the image shown above:
- (1) Press the MODE button.
- (2) Toggle the Up/Down buttons to change the units (0, 5, 10, -95, 100).
- (3) With the correct unit displayed, press the MODE button, which will set the unit and return you to the Options Menu.
To reset service hours after they have counted down to "0.0," reselect the existing setpoint or select a new service hour value.
3. To exit the Options Menu, select the Exit Menu function from the Options Menu; hold the MODE button and exit out of the Options Menu; or do not press any button for 10 seconds, which will exit out of the Options Menu.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
TORX® is a registered trademark of Acument Intellectual Properties, LLC
YouTube® is a registered trademark of Google Inc.
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.